What year did the laserjet 5 printer come out

WHAT YEAR DID THE LASERJET 5 PRINTER COME OUT DRIVER
WHAT YEAR DID THE LASERJET 5 PRINTER COME OUT 32 BIT

It's the successor to the HL-2270, which replaced the 2170, which replaced the 2070. Given your low print volume and limited needs (just B&W) the Brother HL-L2370 is probably your best shot. Plastic gets brittle, grease dries out, etc. Having only 20k prints doesn't matter a lick if the machine is that old. And when they break, well, toss 'em and get a new one. But everything else - from speed and print quality to power use, footprint, noise, etc., - is better.Д«ut they're also cheap.

They make them with about a 5-10 year shelf life, not 20. You say you 'pulled all the boards.' How many boards are there? The ones I know of are the formatter, the control panel and the PSU.Д¬lick to expand.They don't make them as durable. I don't know which ones I should replace. I figure I could do that somehow.ДЄs you indicate, there are other capacitors on the PSU circuit board that I could replace. To my chagrin, all I get now is the soft hiccup responce one/second.Дo you think the PSU is bad? I saw a thread yesterday where a guy tested the voltage of the PSU. Then I removed the PSU and replaced those two tall capacitors. After that I only got the one/second soft hiccup response. Trying again, I got this same sequence once or twice. I'll be damned if it didn't look like it was starting normally! It lit up for the first time since I had put it aside 5 years ago, said it was doing the SELF TEST, but after maybe 5 seconds the three round lights started blinking, the machine's engine was basically hiccuping and after maybe 5-10 more seconds the machine lapsed back into silence with a little hiccup about once/second. Alas, the problem remains.ДЇunny thing is before I did this, before removing the PSU, I tried turning the machine on again in the off chance I'd get a different response.

I swabbed up most of the wetness with Q-tips and put the PSU back together and reassembled the printer, plugged it in and turned it on. I have them at about a 45 degree angle to make sure the cover would fit. They are 1500uf, they didn't have 1200uf, but was assured they would work fine, although they are about 3/16' taller. So, I took my 25w solder iron, after removing enough screws where I could get at the bottom of the board and removed those two capacitors and brought them to my local indy electronics supply store and bought a couple of replacements. I figured there was a good chance it was those two tall 1200uf 35v capacitors. Which capacitors? I could not be certain. I figured that was fluid leaking out of capacitor(s). I didn't notice it at first, but looking closely I saw a lot of wetness on the power supply curcuit board (using a flashlight).

WHAT YEAR DID THE LASERJET 5 PRINTER COME OUT DRIVER

I don't remember seeing improved printing using that driver anyway, and I've found the PCL driver to be incredibly faster in a lot of circumstances.Д¬lick to expand.Ah. I've stopped using the postscript driver altogether the last year or so. I can suggest one thing - don't use the postscript driver, use the PCL driver. I hope to get it working OK before I get an error code! It prints right now but at any time, of course, it could have a problem and I wouldn't be able to see the error code. My replacement used control panel for the HP4M+ came in the mail a couple days ago.

I actually have an extra formatter right now. If your display gets so dim that you can't discern what it says I suppose you need another control panel, possibly the formatter, I don't know. Between them I'm not sure there are over 40,000 prints! I've never replaced the rollers on either of my Laserjet machines.

WHAT YEAR DID THE LASERJET 5 PRINTER COME OUT 32 BIT

I still use that program regularly, it runs on 32 bit systems. I went right out and bought the postscript module for it, something like $250-300 IIRC! I had aspirations to start a career in desktop publishing, had taken instruction in Pagemaker at local night school. The seller was a very tech savvy guy who decided it wasn't for him for some reason. I got it off a listing in the newspaper for a barely used printer. I paid about $1600 for my HP4, and that wasn't even retail. Click to expand.Yeah, they cost a pretty penny back then.

What year did the laserjet 5 printer come out